So after years of wanting to build theses thing I finally ordered the plans and got started on them. I've never dadoed a build before so that part was time consuming. I am just using a circular saw and router. I already have the Audio Nirvana 8's so I am going to use them. Went with the alternate tuning idea. Waiting on the passives to arrive. I do have a question for those who have built these before. How big of a gap is there between the top plate and the plate with the triangle port in it? I couldn't find any dimensions on the pdf plans for it. Also I see some cut a semi circle in the top plate. Does that affect the sound at all? I like the look of if it like that. Here are some of my build pics. Will have more later. Taking my time because I have to wait for the passive to get here before I can listen to them.

Ok I'm gonna try again.

Speakerfreak,

The dim. is on the HDTF&B.pdf shown on the inside of part "A"

The distance between the top of the port plate and the bottom of the top plate is 29-3/4"

Is this what you meant?

zygi

speakerfreak7, thanks for posting. Like Donnie said, makes me want to get out in the workshop. Ages ago, I built some wonderful speakers, but I think I have gotten lazy. So, living vicariously is good. Please keep posting on the progress.

I am making the single driver HDT. Yes that is what I was referring to. Thanks

1.  So how do I make the half circle cut out in the top plate?

2. I have 1.75" egg crate foam laying around. Is that ok to use or should I get the recommended 1" foam?

Personally, I would never go without the dados, alignment of parts is just so much easier. If the port plate is not straight, you'll fight getting the "X" section to bottom out perfectly and seal. If you don't do any dados anywhere else, do the port plate to the sides front and back.

The foam you have there should be fine, around the driver section triangle you need to put two pieces, one above the driver and one below the driver two pieces 3"-4" wide by 18"-19" long and wrap them around the triangle.

Just above, on the very top over the driver hole, there needs to be one piece cut to fit the triangle. If you cut an 8" square then cut that on the diagonal it will make one piece for each cabinet.

ZYGI

speakerfreak,

Do you have the HDTgrill.pdf....If so the layout for the top dispersion plate are on that, you may have missed it.

What I would do is use a piece of scrap, for your center point as the radius is offset by 1/4". Then use a router to cut the 4-1/2" radius.

ZYGI

So the passives arrived today! But I'm not sure what glue is best to use to glue them down? I didn't see in the plans where it said what kind to use. Any recommendations? Or is any fine? I have Super 77 spray glue and weldwood contact cement. Once I glue them is there any way to get them back off without destroying them?

Ok I finished the first one and have been doing a direct comparison with the cabinets they were in which were plans I got with the speakers. I assumed the HDT's would blow them out of the water but it was not so. There was definitely more bass in the HDT's but the midrange was lacking. I'm not worried about bass though because I am using the WO which creates plenty of bass. The only thing I did different was use thicker egg crate but ZYGI said it was ok to do. Someone else said in another thread that they removed the bottom foam in the bottom chamber to help with the midrange. Maybe I need to get the DFR8's to hear their full potential. IDK any ideas?

The bookshelf speakers in the pic are not hooked up. They just wanted to be in the pic to.



I finished the second and set them up and they do have a great sound stage! Vocals in the center and the other instruments placed where they would be live at a concert! Although the other cabinets had pretty good sound stage as well. I have my old system setup so that I can swith back and forth to see how much better this one is. The other system is just a Pioneer receiver and the tritrix speakers I built from partsexpress and both systems use the BASH 500 amp with the WO with the decware 10's. (Nails coming out of the sheetrock!) The new one is the HDT's with the Audio Nirvana 8's, HRT Music Streamer II DAC, 8 watt tube amp diy kit from tubedepot.com and the WO. I play FLAC files from Foobar.



The new system is so much better!!!! A DAC is a must have when
playing music from the comp.  When I swith to the old system the sound seems condensed and confined to small space. I have to turn the Pioneer amp way up to keep up with the new system. I only have the tube amp turned up half way and it gets really loud!