Forums - select current draw

Welcome, Guest. Please Login or Register

05/02/25 at 18:00:26

Most recent 50 posts

Forums › OLDER DECWARE GEAR SUPPORT › SE84CS, SE84ZS

‹ Previous topic | Next topic ›

Pages: 1

select current draw (Read 12655 times)

lightmaster Senior Member life is too short for bad hifi. Really! Posts: 72	select current draw 02/17/07 at 00:44:53 hei guys do you know how much current does the select draw? thxs f
Back to top	“Everything should be made as simple as possible, but not simpler.” Albert E. IP Logged

9anda1f

Ex Member

Re: select current draw
Reply #1 - 02/17/07 at 01:13:51

Select CSP2 SPECIFICATIONS

Weight 13 lbs. ea.
Dimensions 8.5" H x 7.250" W x 14.75" D
Circuit type Single ended Class A Triode OTL
Output Adjustable 0 ~ 36 volts
Input voltage 250mv ~ 5.0 volts
Noise / Hum Less than 0.5 millivolts
Input Impedance
100 KOhms
Output Impedance
< 60 ohms
Response 5 Hz ~ 70 kHz
Feedback ZERO negative feedback used
Rectification 5Y3GT tube rectification
Signal tubes 6N1P or 6922 or 6Dj8
Transformers Transformer custom made for this pre amplifier by Decware
Biasing Self-Biasing circuit - never needs adjustment
Resistors All resistors are audiophile grade
Signal Cap Audiophile grade poly film/foil
Filter Caps All filter caps are premium quality
AC cord Fused IEC connector provided with removable power cord
Consumption 65 watts at full power
Input jacks RCA type 24K Gold / Teflon
Output jacks RCA type 24K Gold / Teflon
Headphone jack
1/4 inch stereo jack
Warranty Lifetime to original owner / 90 days on tubes

(Page 10 of the posted owner's manual .pdf)

9anda1f

IP Logged

lightmaster Senior Member life is too short for bad hifi. Really! Posts: 72	Re: select current draw Reply #2 - 02/17/07 at 10:04:45 hei thxs i had that info but what about the current? is it 0.2 AMP??? for a 220 volt unit not very familiar with conversion of electric values???
Back to top	“Everything should be made as simple as possible, but not simpler.” Albert E. IP Logged

rmt Seasoned Member Posts: 238	Re: select current draw Reply #3 - 02/17/07 at 16:56:46 Volts x amps = watts 65 watts/120 volts = .54 amps
Back to top	Select, CSP2 upgrade, Dec 685, DSRii, Nibbelin NFX w/DFR-8s, SE34.I, Zbox IP Logged

Tish Ex Member	Re: select current draw Reply #4 - 02/17/07 at 18:49:27 Hi All, I might be wrong, but I think lightmaster was asking for the currant draw of a select AMP not the CSP2 PREAMP that 9anda1f posted the specs for. Thanks,Tish
Back to top	IP Logged

Rap

Ex Member

Re: select current draw
Reply #5 - 02/17/07 at 23:14:04

Tish wrote on 02/17/07 at 18:49:27:

Hi All, I might be wrong, but I think lightmaster was asking for the currant draw of a select AMP not the CSP2 PREAMP that 9anda1f posted the specs for. Thanks,Tish

Hey Tish, 9anda1f did actually post the correct specs, the only thing wrong was the header Wink

but those are the specs for a select none the less

IP Logged

Tish

Ex Member

Re: select current draw
Reply #6 - 02/18/07 at 18:51:47

Hi All again, The things that got me with those specs are-CIRCUIT TYPE single ended class a triode OTL, RECTIFICATION 5Y3GT tube rectification,TRANSFORMERS transformers custom made for this PREAMPLFIER by Decware, OUTPUT JACKS RCA type 24K gold/teflon, and HEADPHONE JACK. I own a pair of selects and those specs just don't jive with mine. Maybe I'm missing something, Tish

IP Logged

Steve Deckert Administrator If the 1st watt sucks why continue? Posts: 6397	Re: select current draw Reply #7 - 02/19/07 at 04:17:48 Yes, Those were the specs for the CSP2 preamp. The Select amp draws slightly more current - closer to .75 amp Steve
Back to top	IP Logged

lightmaster Senior Member life is too short for bad hifi. Really! Posts: 72	Re: select current draw Reply #8 - 02/22/07 at 20:11:48 thank you guys, i am changing my power cord and needed that info to select the right wire. that is for a 110 volts or my 220 volts? i live in the old continent thxs f
Back to top	“Everything should be made as simple as possible, but not simpler.” Albert E. IP Logged

Hotsauce Seasoned Member Posts: 210	Re: select current draw Reply #9 - 02/24/07 at 12:46:41 My SV83 monos draw 140 W for the pair once warmed up. John C.
Back to top	IP Logged

Pages: 1

Forums › OLDER DECWARE GEAR SUPPORT › SE84CS, SE84ZS

‹ Previous topic | Next topic ›