Forums
https://www.decware.com/cgi-bin/yabb22/YaBB.pl OLDER DECWARE GEAR SUPPORT >> SE84CS, SE84ZS >> select current draw https://www.decware.com/cgi-bin/yabb22/YaBB.pl?num=1171673093 Message started by lightmaster on 02/17/07 at 00:44:53 |
Title: select current draw Post by lightmaster on 02/17/07 at 00:44:53 hei guys do you know how much current does the select draw? thxs f |
Title: Re: select current draw Post by 9anda1f on 02/17/07 at 01:13:51 Select CSP2 SPECIFICATIONS Weight 13 lbs. ea. Dimensions 8.5" H x 7.250" W x 14.75" D Circuit type Single ended Class A Triode OTL Output Adjustable 0 ~ 36 volts Input voltage 250mv ~ 5.0 volts Noise / Hum Less than 0.5 millivolts Input Impedance 100 KOhms Output Impedance < 60 ohms Response 5 Hz ~ 70 kHz Feedback ZERO negative feedback used Rectification 5Y3GT tube rectification Signal tubes 6N1P or 6922 or 6Dj8 Transformers Transformer custom made for this pre amplifier by Decware Biasing Self-Biasing circuit - never needs adjustment Resistors All resistors are audiophile grade Signal Cap Audiophile grade poly film/foil Filter Caps All filter caps are premium quality AC cord Fused IEC connector provided with removable power cord Consumption 65 watts at full power Input jacks RCA type 24K Gold / Teflon Output jacks RCA type 24K Gold / Teflon Headphone jack 1/4 inch stereo jack Warranty Lifetime to original owner / 90 days on tubes (Page 10 of the posted owner's manual .pdf) 9anda1f |
Title: Re: select current draw Post by lightmaster on 02/17/07 at 10:04:45 hei thxs i had that info but what about the current? is it 0.2 AMP??? for a 220 volt unit not very familiar with conversion of electric values??? |
Title: Re: select current draw Post by rmt on 02/17/07 at 16:56:46 Volts x amps = watts 65 watts/120 volts = .54 amps |
Title: Re: select current draw Post by Tish on 02/17/07 at 18:49:27 Hi All, I might be wrong, but I think lightmaster was asking for the currant draw of a select AMP not the CSP2 PREAMP that 9anda1f posted the specs for. Thanks,Tish |
Title: Re: select current draw Post by Rap on 02/17/07 at 23:14:04 Tish wrote on 02/17/07 at 18:49:27:
Hey Tish, 9anda1f did actually post the correct specs, the only thing wrong was the header ;) but those are the specs for a select none the less :) |
Title: Re: select current draw Post by Tish on 02/18/07 at 18:51:47 Hi All again, The things that got me with those specs are-CIRCUIT TYPE single ended class a triode OTL, RECTIFICATION 5Y3GT tube rectification,TRANSFORMERS transformers custom made for this PREAMPLFIER by Decware, OUTPUT JACKS RCA type 24K gold/teflon, and HEADPHONE JACK. I own a pair of selects and those specs just don't jive with mine. Maybe I'm missing something, Tish |
Title: Re: select current draw Post by Steve Deckert on 02/19/07 at 04:17:48 Yes, Those were the specs for the CSP2 preamp. The Select amp draws slightly more current - closer to .75 amp Steve |
Title: Re: select current draw Post by lightmaster on 02/22/07 at 20:11:48 thank you guys, i am changing my power cord and needed that info to select the right wire. that is for a 110 volts or my 220 volts? i live in the old continent :-) thxs f |
Title: Re: select current draw Post by Hotsauce on 02/24/07 at 12:46:41 My SV83 monos draw 140 W for the pair once warmed up. John C. |
Forums » Powered by YaBB 2.2.2! YaBB © 2000-2008. All Rights Reserved. |