Decware Audio Forums
11/22/26 at 12:36:32



Most recent 50 posts
Welcome, Guest. Please Login or Register

Pages: 1
Send Topic Print
Ultimate Decware Accessory (Read 662 times)
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Ultimate Decware Accessory
11/10/26 at 13:21:46
 
Ever since laying eyes on Decware's site back in the late 90s I was drawn  deeper into Steve's work. His site pictorial design kept drawing me back. He seemed to have a knack of turning my eyes over to my time, ears, and eventually wallet. He also offered a free set of plans for the Wicked One at the time. And so it began...

I built a lot of his designs over the last 25+ years with information that is available on his site. Also I purchased kits and plans that are offered by him. I even waited 3 years for the SE84UFO25! Don't get me wrong, finding Decware helped fulfill a life long interest in our surroundings and workings of such. I don't have any regrets and started another project that was inspired by yet another visual of Steve's.

The chimes in his listening room always stood out to me. It seemed odd to have a set of chimes in an audio listening room. The leather wraps made sense to stop unwanted resonance when playin music. I thought it was a just another pleasing visual of the artist in Steve.

A couple of weeks ago I attended the Decfest in Oregon Illinois at the Stronghold Castle where the chimes were on display hanging from the spiral staircase going up one of the towers in the castle. There was a nylon tipped hammer provided to strike the chimes. It was a great experience just striking the long tube at the base of the steps then climb the steps listing to the resonance play out.




This experience stuck out as one of the highlights for me during the fest. Still fresh in my mind after arriving home I remembered reading a blip in this forum of his journey with the chimes. A search began with finding the following:

Quote:
The chimes in the room started with an eBay purchase of 1 inch diameter aluminum chimes from India. These were 9 chimes, tuned to the solfeggio frequencies from antiquity. These specific tunings had nothing to do with music, they were for healing and transformation. From my research despite being used in biblical times all mention of these 7 and later 9 tones have been omitted from the Bible. The highest emphasis you can give to anything is to delete it therefor I became interested in it.

I enjoyed the chimes for about a year and realized two things.... they were not precision tuned and the lower ones like 174Hz did not play 174Hz but rather a harmonic of it like 930Hz or something. Now... if 174 Hz is said to have a specific effect on the human condition, I don't want to waste my time listening to 920/930Hz or whatever it was. I want to hear the fundamental, 174 Hz.

This lead me on a journey to figure out what it would take to make a chime tuned to that frequency that played that frequency instead of some higher harmonic of it. You see, the 1 inch chime did actually play 174Hz, but I remember after measuring it that the 920/930Hz harmonic was 42dB louder!!!!

Through some experimenting I found out that an 1/8 wall 3 inch extruded pipe cut at  60 some inches will hit 174.0 Hz with no harmonics and a sustain time of over 3 minutes. Not to mention the surface area and mass of the chime is like a million times more so it's LOUD. Seems reasonable to me.  If a dim flashlight is good, a bright flashlight is better.  Make no mistake, large chimes like this can change in frequency by as much as 1 Hz with as little a 10 degrees shift in ambient temperature.  I got all of my chimes to within a few 10th of the target frequency, most with adjustable tuning pins that can added or removed if the temperature in the room changes by that amount or more.

I started with the lowest ones, 174Hz and worked my way up. Then I needed something for the other side of the room, so I found the closest chakra frequencies I could to match so I could have chimes on the other side of the room that visually somewhat matched. I got 172Hz on that long pipe, and again worked my way up. Once I got to higher that around 500Hz, the pipe thickness stopped working and the chimes no longer rang. I then found that 1/2 inc wall (8 times thicker) pipe was needed to continue up the scale with similar results.

So these have nothing to do with sound treatment other than being handy little diffusers of high frequencies, they do nothing unless left un-clamped at which point the ring with the music but not being tuned to 440Hz scale they are never actually in tune with the music so the music is ruined by it.

I have figured out that there is no more accurate source of pure tone, or scalar energy than one of these large chimes.  If you spend 20 minutes with them getting them to sink up together when you play them all at the same time is a pretty serious rush.

I have tried to record these and on the DSD recorder once you hit more than 3 chimes at the same time the recording falls apart. You can only do it with reel to reel tape.  So I did.  Then I played the reel to reel tape back on me favorite speaker of the night, and guess what it sounded just like the chimes!  But there was no scalar effect and you could tell it wasn't real...

I have been experiencing these chimes along side two very special singing bowls from Nepal. If I was forced to choose between my stereo or these chimes, despite enjoying the stereo quite a bit more, the chimes are the keys to the universe and must have tools for long term survival.

It's like choosing between Chocolate bars, or fire sticks when on a survival mission and you know if someone makes you choose between your stereo or your chimes, you are on a survival mission.


I built chimes in the past with success. I was always attracted to chimes and the pleasant random tones created. My first set of chimes was inspired by a visit to the Gay Dolphin in Myrtle Beach SC. GD is a multi story store of patched together novelty items. It has a section of wind chimes from very large to small. Swept into imagination and just finishing a new workshop, I shorty build a set of four for each of my family members. The picture below is one on my back deck after 7 years of being beat by Pennsylvania's weather.



The search began for pipe to build a set of Chakra and Solfeggio based chimes. It did not take long to find some brass tube from an old tavern's bar rail. This acquisition took some wild turns that turned out just prefect for my intended use of the chimes.

I usually spend some time in the mornings to check out new offerings on Facebook Marketplace. If something gets my attention and is in good condition I'll save it and let it brew in the old noggin. If the item becomes more center in my vision, I'll send an inquiry and eventually make an offer. If the offer is rejected, 99% of the time I'll let it go. That is how I roll.

The brass pipe offering showed scant pictures of it leaning in the corner of a stuffed storage room. He wanted $500 for it. I asked what size and lengths of the longer pieces. He replied it was 3" and the longer ones were 18' and 15'. Right away I'm thinking heavy .125 wall pipe used most likely for foot rest in the bar. At that price, I ran to meet up with him!



Turns out that the bar was in the valley of my old tromping grounds as a kid. We precariously dug out the pipe. His dimensions were a bit off. It was 2" pipe. The longest was 15' and had a joint about halfway. Hesitating with the sale we worked out a lower price. After, we had a good conversation and reminisced finding common ground with mutual friends shared in the past. I loaded and cut some of the pipe to fit the 8' trailer.

There is one more twist to this purchase that will surface later!

It took a couple of hours to disassemble the pipe from couplings and fittings. Ended up being 114 pounds of brass with 57' of 2" tube and a bucket full of fittings. Just a small percentage over todays scrap price. A good fair deal. 60' of new tube today is $2250!




What I did not shell out in money will be made up with labor. Two cleanings are done at this point. One cleaning with Dawn to remove dirt and oils and another with brass cleaner to remove tarnish. A third and final will remove light scratching after the tubes are cut and drilled.



Pipes are drying after a good rinse. Years of use are evident with scratches and spotting from cleaning. The tavern owner said he took down the pipe after his cleaning crew retired. The spotting was cause by not properly removing cleaner after cleaning. Maybe the new crew did not meet his expectations!



Time to take a break and play with the cats Smiley
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
Lon
Seasoned Member
****
Online

"Love without
guts is
worthless!"
Philip K. Dick

Posts: 29148
Munson Township, OH
Re: Ultimate Decware Accessory
Reply #1 - 11/10/26 at 14:52:16
 
Great score on the local brass! A stroke of fortune there.

I too was immediately drawn to Steve's work, in the mid-nineties. Chimes. . . I'm not drawn to, but I know you love projects and this is a good one for you.
Back to top
 
 

HR-1,ZBIT,ZROCK3,SEWE300B,Dynagrid Jr;Rega RP3+all GrooveTracer mods;PSAudio:PST+DSD DAC Mk II,NPC,PowerBases,AC-12 pwr cbls, Reference spkrcbls,GCHA;Mapleshade SamsonV3;VeraFi Audio cpts VooDoo:Stradivarius interconnects;Stack EQ; phones:Sennheiser HD800S,ZMF Ori
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #2 - 11/11/26 at 11:41:09
 
Quote:
Great score on the local brass! A stroke of fortune there.

Sure thing Lon! I don't fret on missed opportunities just celebrate the ones that fall in place.
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #3 - 11/11/26 at 12:16:25
 
Lee Hite is an accomplished chime designer. His site can thoroughly lead a aspiring novice in building a successful set of chimes. The site is in-depth and complete. I used him on my first build. The site has changed a bit since then. Mainly navigation with familiar landings.

His spread sheet for A4=440 was used to figure out the lengths of pipe for the 14 notes of this project. The editable excel file can be used to find out the length of pipe for any desired frequency taking into account the diameter(OD and ID) and type of material being used.





He recommends to cut the pipe a little longer facilitating fine tuning to the exact frequency if desired. I cut mine about an eight inch longer. The pic below shows one possible layout of the cut pipe. The plan is to hang the pipe on each side of the LED TV in my room. I did a quick buffing of one of the pipes in the picture. Can you find it?



Another possible layout.

   
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
Lon
Seasoned Member
****
Online

"Love without
guts is
worthless!"
Philip K. Dick

Posts: 29148
Munson Township, OH
Re: Ultimate Decware Accessory
Reply #4 - 11/11/26 at 13:26:57
 
I'm not into chimes. . . but I'm into pipe organs and a very similar mathematics is involved in regards to creating notes. I am a descendant of a famous pipe organ builder on my mother's side, and her father was a cabinet maker who studied the science of wooden and sheet metal pipe organ pipes and made a few. And our family has a few of the pipes made by my great great great great great grandfather David Tannenberg.

You have an involving bunch of tasks ahead of you. Enjoy!
Back to top
 
 

HR-1,ZBIT,ZROCK3,SEWE300B,Dynagrid Jr;Rega RP3+all GrooveTracer mods;PSAudio:PST+DSD DAC Mk II,NPC,PowerBases,AC-12 pwr cbls, Reference spkrcbls,GCHA;Mapleshade SamsonV3;VeraFi Audio cpts VooDoo:Stradivarius interconnects;Stack EQ; phones:Sennheiser HD800S,ZMF Ori
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #5 - 11/12/26 at 09:03:03
 
That is interesting Lon. David lived just north of Lancaster PA. One of his organs is located in a Lutheran church in that city. Going to make a point of checking it out the next time I'm traveling in the area. I remember biking thru that city and seeing pianos on sidewalks. I even stopped and played a few cords.
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
Lon
Seasoned Member
****
Online

"Love without
guts is
worthless!"
Philip K. Dick

Posts: 29148
Munson Township, OH
Re: Ultimate Decware Accessory
Reply #6 - 11/12/26 at 10:11:53
 
Yes, my father researched and wrote his first biography about him, and we traveled to Lancaster, Lititiz, et al when I was a lad. His biggest organ was restored in Salem, and the dedication ceremony honored my Mom and her sisters. I've pumped a few of the organs for an organist. Fascinating to have the connection.

Back to top
 
 

HR-1,ZBIT,ZROCK3,SEWE300B,Dynagrid Jr;Rega RP3+all GrooveTracer mods;PSAudio:PST+DSD DAC Mk II,NPC,PowerBases,AC-12 pwr cbls, Reference spkrcbls,GCHA;Mapleshade SamsonV3;VeraFi Audio cpts VooDoo:Stradivarius interconnects;Stack EQ; phones:Sennheiser HD800S,ZMF Ori
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #7 - 11/12/26 at 10:26:48
 
The pic below is the list of target frequencies in the combined Solfeggio and Chakra scales. My working copy.
 


The pipe is ground down to within 1/32" of the target frequency. String is strung thru the drilled holes then the pipe is hung for a final tuning.

I tried using a phone app to set the target frequency. It did no go well with the first attempt. The 963hz pipe came up 1/16" short of the calculated length before the app showed any change in Hz which was much lower then the target. I was also using my ears with another app that played a sine wave target. Should have trusted my ears! Lee mentions on his site if an audio spectrum analyzer shows odd results then trust the measurements.



Lee has an interesting way to mark the hang holes for drilling. He calls it the cigar band method. I'm not going to go into detail here. I used the drill press after marking one side of the pipe when building my first set of chimes years ago. Tried his method this time and it works just as well if not better. Matter of fact, building chimes can easily be done with a basic set of hand tools. Shop equipment makes it much less labor intensive though.

Work area for fine tuning the pipe size and mark hang holes.



I am thinking to do some maintenance on my grounding boxes and add some of this fine brass dust!



Eight more pipes to do then figure how to hang the chimes in the Chariot.

 

Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #8 - 11/13/26 at 09:03:30
 
The chimes are all strung. That was a tedious process. Threading .014" 50 pound fishing line thru two 1/16" holes spanning a 2" inaccessible space was enough to drive me almost nuts! I persevered with determination led on by listening to the results when the pipe, now chimes, were hung and struck. Wow! I will need to work out some kind of apparatus because of the need to restring after the final cleaning or just drill bigger hang holes Roll Eyes

The longest 174 Hz Chime has a sustain time of over 6 minutes. The smallest 963 Hz about a minute. Sustain time seems relative to mass of the chime and striking force. Some of the chimes displayed the wa wa effect. Not sure if it is because of the swinging created after being struck or differences in the welded pipe material. Time will tell on that one.

Next on the agenda is to make two hanging systems, one strictly for display and another for play.

Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #9 - 11/15/26 at 09:39:57
 
Display hanging system done.



DHS is in place with all the chimes hung. This is just the beginning of the finishing process. Each chime will be taken down and fine tuned by ear, buffed to a bright finish, restrung, and hung in proper sequence.



The threading problem was resolved without enlarging the hang holes. The use of a paper clip, Bunch-O-Balloons filling tube, and precision hot plate was used in making a guide for the hang line.

I saved the BOB filling tubes after someone brought a couple packages of the water balloons to camp. The kids loved them and I saw the spoil's had possibilities. My thought was that the individual tube would make good spray nozzle extenders for lubricants and such. It seems that the tubes supplied with the spray cans always get misplaced never to be found again.

The BOB tube was evenly heated on the hot plate and stretched to just the point of being under sixteen inch OD. With the use of the paper clip inserted in one hang hole and the tube in the other HH, the paper clip is easily inserted into the tube serving as a guide to feed the tube in the opposing HH. The fishing line is easily guided thru the reworked BOB tube.



All the chimes can be struck lightly with pleasant results giving enough time to take a seat in the Chariot's sweet spot and enjoy as the vibrations fade Smiley 
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
PDXDrew
Senior Member
***
Offline



Posts: 81
Oregon
Re: Ultimate Decware Accessory
Reply #10 - 11/15/26 at 19:25:45
 
Awesome thread. Thank you for sharing. My eyes went right to Steve's chimes the first time visited his page years ago. Like you, I've always wanted to make a set. Maybe someday. You definitely have inspired. Can't wait to see your finished product.
Back to top
 
 

QSA Veridion Streamer, Lampizator GA TRP 2X12 with RSA Tube Purifiers, Whammerdyne DAA 2A3 amp, Lii P10 in Modified Open Baffle, 2X RELG2, RSA & QSA cables, And Loving it! DGJ on the way...
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #11 - 11/17/26 at 09:38:08
 
Glad to have passed the candle to you Drew. The chimes are complete after about 50 hours of labor.

When looking at a new project, the time that it will take is always front and center. A price is then calculated and added for labor hours. The monetary thing was drilled in all of us since we became cognitive after birth.

Before retirement a $20 figure was the multiplier for hours anticipated to bring items or material up to like new. The sum is used to negotiate a final fair price of the sale. After recently getting some bids to enclose a patio at home, that $20 figure has turned into $50!

Bear with me.
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #12 - 11/17/26 at 12:35:04
 
Time for the final tuning of the chimes. I used an app on the phone to play the target frequency for each chime. The phone was placed on the bench(silver battery is where the phone was placed) and chime hung(left in photo below) to give me a center position as the chime was struck. The initial strike of the chime creates an overtone dependent on the force/material of the striker and mass/material of the pipe. It takes a few seconds before the sound settles into the fundamental(target) frequency of the chime. If the center image between my ears is steady then the chime is at the correct target frequency. If there is a slight warble then it is not. Most of the pipes had a solid steady note at Lee's predictive spread sheet values. Some that I tried to tune using this method did not. Even after adjusting the frequency trying to find what frequency the chime was broadcasting! Could it be variables in the pipe composition created the warble? Anyhow, I trusted Lee's work and used his values to keep my sanity.




The pic below shows the chime after final cleaning. The ends were beveled by rotating on a stationary belt sander. The welded seam can be seen. Extruded pipe does not have a seam and is a better product with a premium price.





Final cleaning of the pipe took about a third of the time for the project. The chimes were buffed three times once with a course wheel, another finer, and then to shine after waxing. I did not have a sisal wheel so scratches remain but the shine of the brass hides those anyways. When the chimes tarnish and all my projects are complete, I may use the sisal to pass the time some day Wink



Restringing the pipes brought up another problem solving task. Lee suggests making an elaborate wood jig to string the pipes for sequence hanging. Great for someone looking to make a production setup. Not for me. I grabbed a few things laying around.




My intention was the hang the pipes in line at the same height on top. I figured that all I needed was a guide to keep all the string lengths the same above the top of the pipe and came up with this:



Fine tuning height after using the guide did not take long. I first tied a square knot to facilitate slippage for fine adjustment then used a half hitch to secure.

Remember my story of acquiring the material for this project and how I ran to get the supposedly 3" heavy wall brass pipe at $500. Well, if it was what I assumed after communicating with the seller it would have never fit in the Chariot using the intended Chakra/Solfeggio scales. The 174Hz pipe hanging at the inner left just clears Bob's SE84 sub amp by 1/8" and just slightly rubs the mounting pin on top mounting bracket for the sound panel actuator! Dollar signs seem to control us all. One 12' 3" .125 wall stick goes for $2400 dollars these days. It would take four sticks to make this project. Material dependent, the larger the diameter and heavier the wall will results in a longer length for the same target frequency with benefits of longer substain time and increased volume.



One more side note. Karen has suffered greatly when her hip was replaced this past July. I was feeling hopeless and helpless with her slow, very slow, recovery after the new femur end dislodged from the hip three weeks after the surgery. In the last nine days, she's been showing great strides of improvement. Her attitude is improving vastly and she even walked down the steps to the Chariot yesterday! As I was working, could the ringing of the chimes have something to do with this Undecided She said she could hear the chimes upstairs!

Smiley
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
Steve Deckert
Administrator
*****
Offline

If the 1st watt
sucks why continue?

Posts: 6624
East Peoria IL
Re: Ultimate Decware Accessory
Reply #13 - 11/19/26 at 20:35:17
 

The chimes look great!  I would say if they didn't work, they wouldn't be documented in ancient texts.  Wishing your wife a speedy recovery : )

Steve

Back to top
 
 
WWW   IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #14 - 11/20/26 at 09:18:41
 
The chimes did fit well in the front wall. 901s are permanently moved to the back wall. The track lights make the chimes come alive when all are struck. Turns out to be a spectacular audio/visual show for 3 or so minutes after being struck and seated.

I've aquire the 3.5" antenna mask pipe. Another wild ride doing that deal. Purchased from a Russian that has yet to master English, he did not seem to understand my particular request from what he pictured in his offering. Anyhow, I ended up with enough pipe to complete the Solfeggio scale. If that works out well he has more. I'll continue with the build here.

The pragmatic side of me wants to think that my wife was just about to turn the corner in her recovery. However, the physic in me knows better. I'm a believer!

Thanks for the well wishes Steve.
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
JBzen
Seasoned Member
****
Offline



Posts: 1756
Irwin PA
Re: Ultimate Decware Accessory
Reply #15 - Yesterday at 10:30:01
 
The next progression of my Decware experience naturally turns to the outdoors. I would happily live outdoors if located in a moderate climate. Pennsylvania winters prevents that ideology. Steve even placed his Headwreckers on a concrete slabs' anchored to oak tree roots. I unfortunately missed that Decfest!

Five 8' galvanized pipes with a wall thickness of .165" was acquired for a set of Solfeggio based chimes that will be hung on the side deck of home. The increased mass as compared to brass will create a need for special handling. The 174Hz chime will increase in length by almost 50% and weight 6 times as much. An abrasive cut off saw will be used instead of a hack saw for sizing the pipe. A grinder will be used instead of a belt sander for final tuning. Stainless steel cable will be required for hanging. More strenuous and brutal actions for sure!





The worksheet:





Smiley
Back to top
 
 

{LoopA[AMC CD8b>XO3>Stokes DAC>Carver C-9]LoopB[Ortofon 2M Black>Scout jr/Otari MX5050B2>ZP3]LoopC[Cambridge CXN2>ZDAC>ZBOX]}Zrock3>CSP2+>SE8425th>OCC copper braid>lii Crystal 10". Isolation. AC filtering. EcoFlow R2Max, Room Treatment.
  IP Logged
Share: X Facebook LinkedIn Email WhatsApp Instagram Likes:
Pages: 1
Send Topic Print