Forums - Loose/stripped power cord input screws?

07/04/26 at 14:59:14

Most recent 50 posts
Welcome, Guest. Please Login or Register

Forums » ZP3 / ZMC1,2,3

‹ Previous topic | Next topic ›

Pages: 1

Loose/stripped power cord input screws? (Read 6557 times)

attym Verified Member Offline Posts: 29	Loose/stripped power cord input screws? 10/15/14 at 16:54:01 Hello, on my ZP3, the power input seems to be a bit loose. Perhaps from the weight of the power cord. When I go to tighten it, it seems stripped and won't tighten any more. Its just not snug but I could leave it as is. Has anyone run into this issue? Any solution? Drive a bigger screw in there? Thanks
Back to top	IP Logged Share: Likes:

Syd Seasoned Member Offline Posts: 1534 Essex Uk	Re: Loose/stripped power cord input screws? Reply #1 - 10/15/14 at 20:56:22 silver paper or small slither of wood in the screw hole will get it tight again..just.
Back to top	Decware: Rachaels x 2 bridged, C. SP2+, ZP3, ZMC1, DHC-1 pw/cbl`s Michell Orbe + SME V + M.Benz LP s, Arcam CD33, Nakamichi LX5, Lowther acoustas DX2`s, WE 16g sp/cbl`s, Isotek mains substation, M & K subwoofer, Belden 8402 interconnects. IP Logged Share: Likes:

hdrider

Seasoned Member

Offline

On the path with
Decware.

Posts: 719
Santa Cruz Mtns. Ca.

Re: Loose/stripped power cord input screws?
Reply #2 - 10/16/14 at 04:19:14

While I have not received my ZP3 or Rachel yet… it looks like the IEC power socket is on the chassis, not the wood case. There must be a nut on the other side that is just spinning when you try to tighten the screw. It shouldn't be too much to remove the screws on top and get inside to check it out. OF COURSE, un-plug it and remove the tubes and remember that the capacitors will hold a BIG charge for a long while so do not touch them. Or call Zen Master Steve and ask him what to do. Be careful and happy listening, Chris.

CSP3, Rachael, ZP3, ZMC 1, Sony ES Bluray, Schitt Bitfrost DAC,Sota Star TT w/ FR-64, Hana SL Low Output Moving coil, Omega 7XRS Mk 2 walnut, DeepOmega 8 sub, Beldon 8402/Switchcraft IC's, Gamma Electrostatic phones.

IP Logged

Likes:

attym Verified Member Offline Posts: 29	Re: Loose/stripped power cord input screws? Reply #3 - 10/16/14 at 15:43:31 why didn't I even think there would be a nut on the other side? I will dig in...
Back to top	IP Logged Share: Likes:

hdrider Seasoned Member Offline On the path with Decware. Posts: 719 Santa Cruz Mtns. Ca.	Re: Loose/stripped power cord input screws? Reply #4 - 10/22/14 at 03:01:52 attym- did you fix it?
Back to top	CSP3, Rachael, ZP3, ZMC 1, Sony ES Bluray, Schitt Bitfrost DAC,Sota Star TT w/ FR-64, Hana SL Low Output Moving coil, Omega 7XRS Mk 2 walnut, DeepOmega 8 sub, Beldon 8402/Switchcraft IC's, Gamma Electrostatic phones. IP Logged Share: Likes:

Pages: 1

‹ Previous topic | Next topic ›