Forums - New to SE34 Rachel Amp

Welcome, Guest. Please Login or Register

04/23/24 at 23:45:23

Forums › EQUIPMENT FORUMS › SE34I.5

‹ Previous topic | Next topic ›

Pages: 1

New to SE34 Rachel Amp (Read 11591 times)

FullRangeMan

Verified Member

Posts: 24

New to SE34 Rachel Amp
04/12/15 at 22:32:33

Hi folks,
Iam new to the Forum and to Rachel too.
I completly unknow how is the Rachel inside, so I apologize in advance for the many questions.
I would like to clear some doubts I dont see answer in the Rachel page.

1) Rachel use ceramic sockets or Teflon?

2) What wire is used, copper, silver, PVC, Teflon, Cotton?

3) It have soft start? How many seconds?

4) There is 2 power on switches for filaments and HV or just 1 for both?

5) I can order Rachel as monoblocks in the CSP3 box?

Thanks,
Gustavo

To whom more was given more will be required.

IP Logged

Syd Seasoned Member Posts: 1534	Re: New to SE34 Rachel Amp Reply #1 - 04/13/15 at 15:39:48 FullRangeMan The power tubes meter indicators start moving after around 4 seconds. There is just one on/off switch. To order 2 Rachaels for use as monoblocks you just order 2 on the SE34 order page. To bridge them is made easy.
Back to top	Decware: Rachaels x 2 bridged, C. SP2+, ZP3, ZMC1, DHC-1 pw/cbl`s Michell Orbe + SME V + M.Benz LP s, Arcam CD33, Nakamichi LX5, Lowther acoustas DX2`s, WE 16g sp/cbl`s, Isotek mains substation, M & K subwoofer, Belden 8402 interconnects. IP Logged

FullRangeMan Verified Member Posts: 24	Re: New to SE34 Rachel Amp Reply #2 - 04/13/15 at 16:22:06 Thanks for your reply Syd. I dont want run PP or PSE so 2 Rachel amps dont serve me. Do you confirm this is the Steve/factory position?? Thanks
Back to top	To whom more was given more will be required. IP Logged

Syd

Seasoned Member

Posts: 1534

Re: New to SE34 Rachel Amp
Reply #3 - 04/13/15 at 18:48:20

The factory position is up to you. On the shop page you can choose what and how many inputs and volume controls you need to use as an integrated.
So you might want 2 channel volumes and a master volume with 3 inputs.
Or you may want 0 channel volumes and a master volume and 2 inputs.

Then there are the other options... base, signal caps, stepped attenuators, silver RCA`s, knobs....

I have no volumes and control through pre amp.

Decware: Rachaels x 2 bridged, C. SP2+, ZP3, ZMC1, DHC-1 pw/cbl`s Michell Orbe + SME V + M.Benz LP s, Arcam CD33, Nakamichi LX5, Lowther acoustas DX2`s, WE 16g sp/cbl`s, Isotek mains substation, M & K subwoofer, Belden 8402 interconnects.

IP Logged

FullRangeMan

Verified Member

Posts: 24

Re: New to SE34 Rachel Amp
Reply #4 - 04/13/15 at 22:48:30

Thanks Syd.
I may have to ask about monoblocks to the factory staff, I will leave that for last case, for not to take their time.
I want two chassis and two power supplies.
A dual mono in one chassis also dont suit to me.

About the soft start by what you said Rachel dont have it.
Usually soft start are 10 or 15 seconds where the wall incoming voltage will rising slowly until reaching the nominal value that in my case is 220V.

To whom more was given more will be required.

IP Logged

Doorman Seasoned Member "pouring from the empty into the void" Posts: 450	Re: New to SE34 Rachel Amp Reply #5 - 04/13/15 at 23:26:56 Why not contact Steve directly with your questions, "go to the horses mouth" as it were ?
Back to top	Decware, Rega, Heybrook/Linn/Ortofon Goertz/Wireworld/cat-5/MarkAudio Alpair 10.2 drivers (eN) in DIY Mar-Ken cabs NHT SB3’s IP Logged

FullRangeMan Verified Member Posts: 24	Re: New to SE34 Rachel Amp Reply #6 - 04/14/15 at 00:53:35 Do you feel they like to answer many questions from overseas NON-custumers? They like custom orders?
Back to top	To whom more was given more will be required. IP Logged

FullRangeMan

Verified Member

Posts: 24

Re: New to SE34 Rachel Amp
Reply #7 - 04/18/15 at 22:12:54

I emailed Steve and have received some interesting responses:
- The Rachel use ceramic sockets as the Teflon sockets had many problems.
- Wiring is copper with PVC and Teflon jackets, signal path is Teflon.
- If I understand Steve right Rachel use around 10 seconds softstart.

Now Iam waiting Steve informing the price for two monoblocks to place my order.

To whom more was given more will be required.

IP Logged

hdrider Seasoned Member On the path with Decware. Posts: 695	Re: New to SE34 Rachel Amp Reply #8 - 04/25/15 at 15:52:38 FullRangeMan- I am sure that you will love your two Rachael amps when you get them, and get them broken in. I love mine (single) driving my Omega 7XRS speakers and the ZP3 just makes the turntable sing. Happy listening, Chris.
Back to top	CSP3, Rachael, ZP3, ZMC 1, Sony ES Bluray, Schitt Bitfrost DAC,Sota Star TT w/ FR-64, Hana SL Low Output Moving coil, Omega 7XRS Mk 2 walnut, DeepOmega 8 sub, Morrow Audio PH3 and MA3 IC's, Gamma Electrostatic phones. IP Logged

FullRangeMan Verified Member Posts: 24	Re: New to SE34 Rachel Amp Reply #9 - 04/26/15 at 04:57:06 Thanks Chris, I have a 7A pair stored. No luck so far, yet waiting the monoblocks price quote from Steve. Regards
Back to top	To whom more was given more will be required. IP Logged

Pages: 1

Forums › EQUIPMENT FORUMS › SE34I.5

‹ Previous topic | Next topic ›

UPLOAD IMAGES HERE