Forums - Peerless XLS-10" @ WO32?

Welcome, Guest. Please Login or Register

04/18/24 at 09:31:57

Forums › SUPPORT FORUMS FOR DECWARE SPEAKER PLANS › WO32 Support Forum

‹ Previous topic | Next topic ›

Pages: 1

Peerless XLS-10" @ WO32? (Read 15220 times)

Hezzu Ex Member	Peerless XLS-10" @ WO32? 03/10/07 at 18:35:35 Can u use Peerless XLS-10 at WO32? http://www.tymphany.com/datasheet/printview.php?id=32 Would it sound any good...?
Back to top	IP Logged

rmt

Seasoned Member

Posts: 238

Re: Peerless XLS-10" @ WO32?
Reply #1 - 03/10/07 at 19:21:22

DHM-108
* Qms: 7.49
* Qes: .33
* Qts: .618

Peerless XLS
Qms 2.63
Qes 0.18
Qts 0.17
I. Rigid Cast Aluminum Basket
The rigid cast basket with an aerodynamic profile provides the necessary sturdy base for the magnet structure and suspension and allows for the 44 mm max excursion of the cone.

Those numbers don't look aligned with the Dec speaker. I do not know what the specs are for the Vifa driver that has been recommended too. I could be wrong but I think that is a lot of excursion for this box. I thought I read that the box will dampen the xmax too.

Select, CSP2 upgrade, Dec 685, DSRii, Nibbelin NFX w/DFR-8s, SE34.I, Zbox

IP Logged

Hezzu Ex Member	Re: Peerless XLS-10" @ WO32? Reply #2 - 03/10/07 at 20:09:39 Thx rmt, 4 quick reply..! Maybe I build WO32 enclosure and try... And maybe I should wait for more answers...
Back to top	IP Logged

ZYGI Seasoned Member HR-ONE Posts: 757	Re: Peerless XLS-10" @ WO32? Reply #3 - 03/10/07 at 20:29:12 Hezzu, The XLS series of Peerless drivers would probably be the worst driver to use in the WO-32. It has nothing to do with the the specs, other than the extreme excursion, it has more to do with the suround used to get the extreme, and the shape of the cone. Bob Z
Back to top	All Decware amps and sources, Turning Point Audio speakers IP Logged

Hezzu Ex Member	Re: Peerless XLS-10" @ WO32? Reply #4 - 03/10/07 at 20:44:16 The XLS series of Vifa... not Vifa, peerless... ...anyway...
Back to top	IP Logged

ZYGI Seasoned Member HR-ONE Posts: 757	Re: Peerless XLS-10" @ WO32? Reply #5 - 03/10/07 at 20:47:48 I was changing that when my cat decided to sllep in my chair My mistake!!!! Either way, it will not wrk!!! Bob
Back to top	All Decware amps and sources, Turning Point Audio speakers IP Logged

larry Ex Member	Re: Peerless XLS-10" @ WO32? Reply #6 - 03/10/07 at 20:50:04 I'm using XLS-10" woofer in my WO-32. On loud passages it hits the maget, it makes a pinging sound. I got these really cheap on Ebay. I'm switching to the woofer sold at Decware. It does make claen, deep base but can't take any serios power. The WO-32 ROCKS. Larry
Back to top	IP Logged

Hezzu

Ex Member

Re: Peerless XLS-10" @ WO32?
Reply #7 - 03/10/07 at 20:57:37

Thx Larry!

I just bought two mono amplifiers for my subwoofers and they cost around 700€...
http://www.bkelec.com/MODULES/bsbpv300.htm

Dont have enough money to buy Vifa's but I think that I'm going to build one WO32 anyway.... next month I have enough money to buy more drivers...

Now I drive those sub's with an old JVC integrated amplifier...

(105wats@4ohm)

IP Logged

ZYGI Seasoned Member HR-ONE Posts: 757	Re: Peerless XLS-10" @ WO32? Reply #8 - 03/10/07 at 21:05:25 Larry, I think what your hearing there is the cone flexing, amplified by the horn it can sound pretty ugly. The cabinet damps the driver so well, I don't think you could run the XLS to its max excursion in that box, and with enough power something has to give, its going to be the cone. And yes, they do rock!!!! Bob
Back to top	All Decware amps and sources, Turning Point Audio speakers IP Logged

larry Ex Member	Re: Peerless XLS-10" @ WO32? Reply #9 - 03/10/07 at 21:30:03 I showed Steve a picture of my WO-32 that I built. I also told him about the peerless XLS drivers pinging at loud passages. His solution was to change to the driver that was made for the box. Larry
Back to top	IP Logged

Pages: 1

Forums › SUPPORT FORUMS FOR DECWARE SPEAKER PLANS › WO32 Support Forum

‹ Previous topic | Next topic ›

UPLOAD IMAGES HERE